Skip to content
Lucidus

Explore Lucidus

LucidusBuy now · $149.97

First production run · Made for makers

The Standardized
E-Mesh Kit

A regulated mod, a mesh deck and a one-piece glass chamber with the mouthpiece built in. Every kit is the same hardware, so settings and notes carry from one owner to the next.

e-mesh: heated by a flat mesh screen · mod: the battery box · mesh deck: the part that holds the screen

Lucidus with Bulb glass
Shown with Bulb glass
Mesh deck
Ø26 mm
Mesh
200-mesh SS316L
Mod
68.6 g
Power
14 to 24 W
Battery
Single 18650
Glass
Three setups

Four Parts, One Stack

Four parts, named on the photo.

FIG. 01Anatomy · side viewCylinder glass fitted

Numbers match the kit list.

New to E-Mesh?

  1. 1The mod sends battery power to the mesh deck.
  2. 2The flat screen on the mesh deck heats when powered.
  3. 3Air enters at the base of the mesh deck and crosses the hot screen.
  4. 4The vapor rises through the glass to the mouthpiece.

First Use

  1. 1Charge the mod with the USB-C cable.
  2. 2Check the screen sits flat under both clamp bars.
  3. 3Burn in a new screen gently: short pulses at 20 W, cooling between, until it glows evenly. A slightly uneven glow is fine. If one corner glows much brighter, reseat the screen.
  4. 4Open two airflow holes and set Power mode (P) at 20 W. P is the only mode you need to start.
  5. 5Load the screen, fit the glass, and fire. Our testing settled near 24 W with two holes open.

Everything in One Box

US kits have 14 parts. International kits have 13, because the battery ships only inside the US.

$149.97plus shipping
Buy now$149.97

Mod, mesh deck, Cylinder glass, Bulb glass, percolator, top airflow vent, 20 screens, clear side panels, decals and stickers, loading tool, screws and screwdriver, USB-C cable, scale tray.

Battery included in US kits only.

  • 30-day returnsSend back an unopened kit for a full refund.
  • Defective parts replacedTell us within 30 days. We replace the part or refund the kit.
  • Ships by USPSTracking is emailed when your order ships.
Open Lucidus kit showing the mod and included components
Presentation image. Packing may vary.

The countTap a part to enlarge. Numbers match the figures.

Mod · powered bodyQty 1
Mesh deckQty 1
Cylinder glassQty 1
Bulb glassQty 1
PercolatorQty 1
Top Airflow VentQty 1
Screens · two widthsQty 20
Clear side panelsQty 1 set
Decals + stickersQty 1 set
Loading toolQty 1
Screws, gaskets, driverQty 1 set
18650 batteryUS orders onlyQty 1
USB-C cableQty 1
Scale trayQty 1
14partsUS kit

06 adds top airflow. 10 is a rest for loading the screen.

Built to Fit Together

Close-ups of the parts that matter.

FIG. 02Mesh assembly0.05 mm wire · laser-cut edges
The device with Cylinder glass held in one hand, to show its size (retouched).
AFire button
BDisplayOLED
CButtons
DCircuit boardBehind window
  1. 03Cylinder glass
  2. 02Mesh deck
  3. AFire button
  4. BDisplayOLED
  5. CButtons
  6. DCircuit boardBehind window
Retouched photo
FIG. 03In handWhite Delrin · clear side panels · USB-C

Three Setups in Every Kit

Two glass pieces and one steel percolator, all on the same mesh deck. Everything comes off by hand.

Pick a glass. The photo and the details change.

Lucidus with the Cylinder glass piece fitted
Configuration 1 of 3

Cylinder Glass

Short, Straight Vapor Path

A straight-sided chamber keeps the vapor path short and direct. The Cylinder glass is our recommended starting configuration.

The chamber and the mouthpiece are one piece of glass. No separate drip tip. After the screen, vapor touches only glass.

Chamber
Straight-sided
Percolator
Not fitted

Build and care

How It Fits Together

Every part from the bottom up, plus screens, airflow, loading and finish.

Exploded view, screens, airflow, loading, finish
FIG. 05Exploded viewBottom to top

Numbers are kit numbers. Select a row to open that part in the kit list.

Screens

Two Widths, Included

Two widths, two airflow and resistance options. Every screen is laser-cut, so the edges are clean. Ten of each. The narrow one is installed. Swap a screen when it wears.

NarrowInstalled

Full-widthMore mesh

Fig. 06The two screens, drawn to scaleSS316L · 200 mesh · laser-cut · weave enlarged to show it
Airflow

Adjustable Airflow

The mesh deck has adjustable bottom airflow. The Top Airflow Vent adds top airflow, for people who prefer it. It is designed for a smoother draw. You can use both together, for example one hole open on top and one on the bottom.

  1. 06Top Airflow VentOptional. Included.
  2. 02Mesh deckThe vent sits on top.
  3. 03·04GlassGoes on top of the vent.
Fig. 07The vent seats on the mesh deckIllustration · parts redrawn at one angle
Loading

A Rest for Loading

The loading tool sits on the mesh deck, over the screen. Rest your folded paper or weigh boat on it while you scrape material onto the screen. It works best with the full-width screen. Go slow for a clean load.

  1. 10Loading toolSits on the mesh deck.
  2. 07Mesh screenUnder the opening.
  3. 02Mesh deckThe tool sits on top.
Fig. 08The loading tool sits over the screenIllustration · parts redrawn at one angle
Finish

Make It Yours

The clear side panels come off. Put the stickers under them. Apply a battery decal over the factory wrap.

Specifications

Specifications and Controls

Figures are for the kit that ships. Tap a mode to see it on the screen.

Recommended range14to24W
141618202224TESTED

New to this? Use Power mode (P) with two airflow holes open. Our testing settled near 24 W.

01Mesh deck
Ø26 mm304 stainless steel
02Mesh
SS316L200 mesh0.09 to 0.11 Ω
03Power
Single 18650, flat top3000 mAh · 15 A minimum
04Interface
OLEDUSB-Cthree buttons
05Body
81 × 35 × 26.6 mmwhite Delrin, one block
06Mod weight
68.6 gglass: hand-blown borosilicate
07Cut-off
84 °C10 s fire limit
08Glass
Three setupsone mesh deck
Controls

Three Buttons, Four Gestures

Fire × 5Lock or unlock the mod.
Fire × 3, then + / −Open the mode menu and step through modes.
Screen showsResistance, volts, watts, mode, battery, puff counter.
Switch offThe screen and the fire-button light can each be turned off.
Safety cut-offs

Five Conditions the Board Stops For

Tap a cut-off to see it on the screen.

Interactive demo · sample readingsSchematic · mm
81 mm26.6 mm10V+−
Screen, enlargedReady
Hold fire to fire. Press it ×3 for the mode menu, ×5 to lock.

Screen: mode P, 18.0 watts, 0.10 ohms, 0 puffs, sample values.

Sample screen readings, not measurements.

Board modes
Standard

Power mode · P

Set the watts and fire. The board holds that power steady as the battery runs down.

Good for

Setting a number once and getting the same result every puff.

Good to know

Our recommended settings, 14 to 24 W, are written for this mode.

Heat-up at the start of a puffIllustrative, not measured
SET POWER · SAME IN ALL THREETIME FROM START OF PUFF →POWER TO MESH →ILLUSTRATIVE · NOT MEASUREDP2P1P
t = 12% of window · % of set power, illustrative
P2 · 1st to rise75%
P1 · 2nd to rise47%
P · 3rd to rise30%

Same watts in every mode. The curves differ only in how fast each reaches the set power. No wattage or temperature values are shown because none were measured. Move across the chart to read the order at any moment.

1 of 7
Materials

Body: one block of white Delrin · Glass: hand-blown borosilicate · Mesh deck: 304 stainless steel · Screens: SS316L, laser-cut

Owner reports

The Manual Keeps Improving

We collect owner feedback, compare it, and update the instructions when reports agree. The same reports inform possible future designs.

How reports are used
  1. Owners report

    Which mode, which screen, which watts, and what you saw. Short notes are enough.

  2. We compare

    When several owners see the same result, it goes into the instructions. Open questions stay marked as open.

  3. Designs follow the data

    Patterns across many reports show what to keep, what to change, and what to build next.

Made for makers

First production run · Open beta

This is our first production run, so think of it as an open beta. It is a tool for people who like to adjust, test and take notes, not a sealed consumer product.

You will swap mesh screens, seat parts by hand and learn what your setup likes. We are still testing and refining parts of the kit, and later runs will change as we learn.

If you want something that works the same with no setup, this kit is not for you.

Known Issues

We list what we know, including what we have not solved.

OLED display
On some mods, the OLED display scrambled or flickered during our checks. We are still finding out how many. If yours does this, we will replace it.
“SHORT” warning
The OLED display can show the word SHORT. It is rare, and it has not been much of a problem. If it appears, reseat the mesh screen and try again.
Uneven heat
Some uneven heating is probably common to all mesh setups. A mesh screen that is clamped unevenly makes it worse. Check the glow and reseat it if needed.
Power
In our tests the volts fell during a fire. We are still testing whether the watts on the display hold steady.
Temperature control
These modes have had very little testing with our mesh screens.

FAQ

Common Questions

New to e-mesh

What is e-mesh?

E-mesh uses a flat stainless-steel mesh screen that heats electrically, instead of a wire coil.

What is a mod?

The mod is the battery box. It holds the 18650 battery and supplies regulated power.

What is the mesh deck?

The mesh deck is the part that holds the mesh screen. Air comes in through holes at its base, and the glass sits on top of it.

What can I use it with?

Dry materials only. It is not designed for liquids, e-liquids or oils, and it has no tank, wick or reservoir. Do not use it with liquids.

Buying

What else do I need?

US kits: nothing else. International kits: one flat-top 18650 battery.

Is a battery included?

US kits include one battery. International kits ship without one. Use a flat-top 18650 rated 3000 mAh and at least 15 A continuous. 20 A or more is better.

Setup and screens

How much assembly is required?

Some assembly is needed. The mesh screen arrives installed.

Why are two screen widths included?

The two widths give different airflow and resistance. Ten of each are included, and the narrower screen arrives installed.

Already own one? Open the owner's guide →

Giving back

Every kit gives back.

Five percent of the profit from every kit goes to veteran mental health. We post each quarter's receipt here so you can check it yourself.

5%of profit, every kit

Giving recordReceipt

  1. Q4 2026First giftPosts when the quarter closes

Given so farFirst receipt posts January 2027

First production run · Made for makers

The Standardized E-Mesh Kit

Fourteen parts in one box. Every kit is the same hardware.

Buy now$149.97